MOOSE Z950 Uživatelský manuál

THESE SYSTEMS HAVE BEEN DISCONTINUED Table Of Contents Z900 and Z950 1. Operating Your System 1.1 System Orientation . . . . . . . . . . . . .

Automatic Interior Off/Delay Off Your system may have been programmed to automatically turn the interior zones off if you arm and do not leave th

1.3 Disarming Disarming Upon Entering The Premises Your system is programmed with one or more entrance delay zones which allow time to enter the

1-6 User's Manual

1.4 Alarm Conditions What To Do If An Alarm Occurs Whenever an alarm occurs, the ALARM indicator will light, the audible alarm will sound (if ap

User's Manual 1-7

1.5 The Keypad Panic Alarms Your system may have been purchased with up to three keypad panic alarms. These may be used to activate an alarm in t

1-8 User's Manual

1.6 Special Features Chime Mode Operation The CHIME mode allows audible monitoring of zones while the system is dis-armed. When the CHIME mode is

User's Manual 1-9

Bypassing Zones The Bypass (#) key is used to bypass selected zones in your system. A bypassed zone will NOT be capable of activating an alarm as

Key Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11 Arming . . . . . . . . . . . . . . . .

1-10 User's Manual

To Cancel All Zone Bypasses I. Press the Bypass (#) key followed by key “9" 2. All ZONE indicators will stop flashing.

User's Manual 1-11

Access (U.L. Note: The control is not listed to Standard U.L. 294 Access Control Units.) If your system was purchased with the ACCESS feature, th

1-12 User's Manual

Audible Zone Testing With Bell Test and Dialer Test NOTE The bell test and dialer test are not available on the Z900. The TEST mode commands th

User's Manual 1-13

7. Violate a detection zone (open a door, window, etc.). The keypad will beep continuously and the indicator of the corresponding zone will lig

1-14 User's Manual

1.7 Fire Detection Your system may or may not include fire detection, depending upon the options purchased and the local codes and regulations

Operating Your System 1 1.1 System Orientation NOTE Your security system may consist of either 8 zones, 8 users or 6 zones, 6

User's Manual 1-15

Fire Supervisory/Trouble (Resetting Smoke Detectors) Many smoke detectors "latch on" and illuminate a built-in indicator when trig-gere

1-16 User's Manual

Evacuation Plan 2 2.1 Developing An Evacuation Plan Preparation and education are of prime importance in the preve

User's Manual 2-1

2.2 Fire Prevention And Escape The purpose of heat and smoke detectors is to detect a fire in its earliest stages and sound an alarm, giving you

2-2 User's Manual

Be Prepared Perform fire drills regularly. Use them to assure recognition of an alarm signal. For your protection, simulate different circumstan

User's Manual 2-3

SYSTEM USER REFERENCE User Code #1 __________ User Code #2 __________ User Code #3 ___________ User Code #4 __________ User Code #5 __

each key and its programming are explained on Page 1-8. User's Manual

NOTE: Once every minute the Z900ST performs a self diagnostic test which causes the LCD display to momentarily blink. This is normal operation and s

Programming 3 Certain features of your system are programmable through the keypad. The pro-gramming mode is ent

Changing User Codes Determine your desired new User Code or Master User Code sequence. If you make an error while programming, press the Reset (

3-2 User's Manual

Deleting A Code 1. The system must be disarmed. 2. Press key 9 and hold for three seconds. The keypad will beep three times. 3. Enter the Maste

indicators will blink in sequence with each other when the program ming mode is successfully entered (see remote programming note on Page 3-1 ). Use

4. Press key 6 or key 8, then Bypass (#) key to instruct the control that you wish to program the desired code sequence for Use

3-4 User's Manual

Glossary Alarm Memory: A history of the alarm that last occurred. Arm: To turn the intrusion detection system on. Bypass: To temporarily remove a z

Master User Code (Master User Authorization Code): A code which functions identically to the User Codes; also may be used to enter the programmi

Index A Access ...1-12 Alarm Conditions ...1-7 Alarm Indicator ...1-7 Arme

S Shunting ...1-10 Smoke Detectors Resetting . . . . . . . . . . . . . .1-16 Supervisory/Troub

1.2 Arming Arming The System Prior To Leaving Before your security system can be armed, all of the intrusion zones must be secure as indicated by th

Arming The System Without Leaving Your security system is divided into two areas of protection: 1. PERIMETER - The first line of defense. Con

1-4 User's Manual